Page 1 of 1

DR-MH200 DR-MH300 Problems

Posted: Sat Mar 01, 2008 12:22 pm
by andywilks
DRMH200 Watch for ripple on the 5v rail to the HDD/DVD change C5340
This will give the loading symptom.


DRMH300 Most of these suffer from faulty DVD drives. Even the 'fixed' replacements are failing :cry:
They aren't cheap if out of warranty... and JVC don't always have them in stock...you'll wait weeks.

Posted: Wed Jul 08, 2009 5:39 pm
by kungmats
Hi!

Do you know if 200 is the same as 220?

I got a DR-MH220 that says "Please wait" when I try to start it up and continue with this for hours without starting.
You can also hear the HDD booting, on and on again.

However some times I can make it work if Im lucky and it works just fine until next time ....

The 5v gives me 4.96 with the multimeter and the 12v gives me 11.96.
How ever right now the machine works when I get these results.

I can't find C5340 on the power board. All my C:s has numbers like C103, C104, C105 etc.

Any suggestions?

Posted: Thu Jul 09, 2009 10:55 am
by andywilks
I haven't come across the MH220, and therefore its likely just to be a more modern variation with different circuit boards, hence the component references aren't the same.

However the fault is likely to be the same, so change some of the capacitors- in particular the ones feeding the 12v and 5v rails to the dvd-rom and Hdd connectors. Measuring with a meter at the voltage won't help identify the faulty ones. An oscilloscope is needed to see the ripple on the line

Andrew

Posted: Sat Aug 22, 2009 8:04 pm
by rochusshermit
Hello kungmats,

I have got the same problem with my mh220. It keeps telling my "please wait". Have you got a solution for it?

Thanks for your help!

Posted: Thu Oct 01, 2009 12:57 pm
by andywilks
Response is as above.

If anyone with this model has the circuit references of any capacitors that they replace I would be grateful

Posted: Sun Oct 11, 2009 2:08 pm
by kungmats
Hi!

Sorry for the delayed answer. I didn't notice I got answers :)

I haven't solved the problem yet but I did came over an schematic diagram if some one can help. See the url below.

I've change the capacitators: C121, C123, C124, C125, C133, C134 and C135 on the power board but It didn't help.

I don't have an oscilloscope :(


http://www.wale.se/DR-MH220_yd100sch.pdf


EDIT!
After changing the capacitators above the machine didn't work ... "I thought", but the next time I tryed it it worked just fine, and from that time (at least 2 weeks now) it works just fine. I can plug it out and in to the ac-jacket and it works fine every time. So I guess I punched the wrong buttons on my remote when I tryed the first time after the change.

Posted: Mon Nov 02, 2009 9:52 am
by andywilks
Hi

Thanks for that info.

The most common voltage rail to give trouble is the 12v feed to the DVD drive (yellow pin on the 4 way connector) Often adding a small cap onto this pin and the negative/earth pin next to it will prove it. The correct capacitor on the pcb should still be changed, but this method I've found the quickest to prove..especially if you haven't an oscilloscope.

regards
Andrew

DR-MH200 flashing "loading"

Posted: Wed Aug 25, 2010 9:21 pm
by Marcello
Dear Andy,
Could you please help me to find information to check / or recover the HDD?
Problem is flashing loading.This I've already do:The powersupply was bad, all the caps on the powerboard have been replaced with good (low esr Pan.) caps. All the voltage's are ok without ripple. I've checked the HDD in the PC: it will be reconized in the bios and in the xp devicemanager the drive is visible. Further I did do nothing more with the disk. DVD drive I did check,its ok and working in a pc . Thanks in advance for your reaction!
Marcellino Jansen

Posted: Thu Aug 26, 2010 2:36 pm
by andywilks
If you hold the eject button for 10 seconds while plugging the unit in, does it eventually open the drawer?

If it does open, then the power supply is ok and probably the HDD is corrupt.

Check that then we will talk again
Andrew

Re: DR-MH200 DR-MH300 Problems

Posted: Thu Feb 24, 2011 10:18 am
by Arttu
andywilks wrote:I have the software available for recovering the HDD corruption. contact me if you need it and I will let you know how to get it.

I need the software. I tried some freeware but they just say the disk has errors they can't fix.

Posted: Sat Feb 26, 2011 2:20 pm
by Arttu
The HDD on my unit cannot be fixed, according to Seagate SeaTools the first 109 sectors are bad and it fails the S.M.A.R.T self test.

So, I now have a broken DR-MH200 for sale if anyone needs it. The power supply board is fully functional as I've just spent 70 € to get it fixed. Also the DVD drive and remote are OK.

Send me a message if you need these.

Re: DR-MH200 DR-MH300 Problems

Posted: Tue Jul 17, 2018 8:31 am
by jamie225
good one