Posted: Sat Nov 13, 2010 6:37 pm
new news:
My third item, sometimes failed with loading, lasting a lot of time to come on, so i tried to clone the last original to one of the others disks, so I put this third as master and the seagate as slave, I put the pc with the cd inserted on and it detected only the seagate, after several tests, I noticed the disk didn't rotate, I put it on the jvc and it didnt work. I thought the several tiems it failed was the disk, that was in its end, and moving I killed it definetelly. I remove the electronic card from the other maxtor and it worked again on the jvc, I put the disk on the pc and it died again. I smelt a little burn and saw an SMD transistor (PH45-PB4350 a "big" between the smd's) with a little dot, I looked at the other and had also this little dot. I went to the "museum" and found one 10gb maxtor with a similar SMD, I put it on my disks, on JVC perfect and on the pc, the motor does not run. Voltages are correct, even a little lower than on the jvc, and on this pc are other disks, and is where I "broke down" the firmware of the seagate, but without "burning" it physically.
I bought the SMD's and put on them, my third HDD is now on its machine working fine, I have not tried again on the pc, but i have put the first maxtor, the "guilty" of all and nothing bad happened¿?
Then, I put this hdd on the second jvc and IT WORKED!!!!! yeah, I was so surprised......XDD
I cloned then this maxtor into the seagate, and now I have the seaget on its machine also working. The maxtor guilty is malfunction, I tried the low format level and there are a lot of physical errors.. But at least, the firmware could clone to other.
Now I have a question: I havle cloned into a normal PC 7200 seagate hdd ST380011A, and the one which brings the jvc is ST380012ACE. With the pc HCC (7200) looks it works properly, can this machine work with an 7200 pc HDD?
I have bought on ebay what I mentioned before, and once I have it, I will let you know, what it is and how it works, if it does.
Thank you
My third item, sometimes failed with loading, lasting a lot of time to come on, so i tried to clone the last original to one of the others disks, so I put this third as master and the seagate as slave, I put the pc with the cd inserted on and it detected only the seagate, after several tests, I noticed the disk didn't rotate, I put it on the jvc and it didnt work. I thought the several tiems it failed was the disk, that was in its end, and moving I killed it definetelly. I remove the electronic card from the other maxtor and it worked again on the jvc, I put the disk on the pc and it died again. I smelt a little burn and saw an SMD transistor (PH45-PB4350 a "big" between the smd's) with a little dot, I looked at the other and had also this little dot. I went to the "museum" and found one 10gb maxtor with a similar SMD, I put it on my disks, on JVC perfect and on the pc, the motor does not run. Voltages are correct, even a little lower than on the jvc, and on this pc are other disks, and is where I "broke down" the firmware of the seagate, but without "burning" it physically.
I bought the SMD's and put on them, my third HDD is now on its machine working fine, I have not tried again on the pc, but i have put the first maxtor, the "guilty" of all and nothing bad happened¿?
Then, I put this hdd on the second jvc and IT WORKED!!!!! yeah, I was so surprised......XDD
I cloned then this maxtor into the seagate, and now I have the seaget on its machine also working. The maxtor guilty is malfunction, I tried the low format level and there are a lot of physical errors.. But at least, the firmware could clone to other.
Now I have a question: I havle cloned into a normal PC 7200 seagate hdd ST380011A, and the one which brings the jvc is ST380012ACE. With the pc HCC (7200) looks it works properly, can this machine work with an 7200 pc HDD?
I have bought on ebay what I mentioned before, and once I have it, I will let you know, what it is and how it works, if it does.
Thank you