Page 1 of 1

HD not boot

Posted: Fri Jul 28, 2006 6:52 pm
by zoritsu
Hello:
An icon has been lit flashing in the display. The blue light of
functioning of the hard disk is subdued. I have proved to connect it
to the current having touched the buttons of ignition and stop.

You have idea of that it can mean and of his possible solution.

Thank you.

Posted: Fri Aug 04, 2006 2:37 pm
by Andy Cippico
Hi zoritsu,

Sorry, I don't have an answer for that. I don't know the HDS4 very well. Perhaps Andrew W (moderator on this forum) has an idea.

Andy

Posted: Fri Sep 29, 2006 11:25 am
by andywilks
Sorry not to have responded earlier.

Its difficult to establish exactly what symptoms you have.

If you are getting odd characters on the (front panel) display and the blue light flashing then its trying to boot. Only when successful does it remain lit blue constantly. random display characters is an indicator of a more serious problem than just HDD corruption however.

Posted: Wed Oct 11, 2006 12:12 am
by resistor
Hi

I seem to have exactly this same problem. There is an icon comprising a straight line and an arrow pointing to the right. The blue light for the hard drive does not come on. I had this same problem some time ago at which time i left the hard drive unplugged for about 24 hours and it then seemed to reset itsel. I have tried it this time but without success. Any advice would be appreciated.

Posted: Wed Oct 11, 2006 12:13 am
by resistor
one other thing. The vhs side of things is working fine.

Posted: Wed Oct 11, 2006 3:47 pm
by andywilks
It is most likely the HDD which is failing. A common problem is that the drive when warm will act up. Letting it cool down may temporarily provide a cure. If now it can't fully boot due to corruption, then you need either to clone a working drives image to the HDD, if the drive is still physically ok or more likely you'll need a fresh drive (with JVC OS on it)

I can provide complete new drives with image for ?75- tested too!

Posted: Thu Oct 12, 2006 10:03 am
by resistor
This is not a drive problem as I have tried two cloned drives which I have tested previously.

Posted: Thu Oct 12, 2006 11:18 am
by andywilks
In that case there must be a problem with the processing for the digital section- something I have not had happen before.

If it can be intermittent then its possible one of the processing IC's or memory Ics might have dry joints on the legs/pins. Its not really a DIY job to attempt to find them though.

the same has happened again

Posted: Fri Nov 09, 2007 1:03 am
by zoritsu
Hello:

Today have happened three electrical interruptions of approximately four seconds each one, and it has happened again.

I remember that the previous time was a fall of tension prolonged during the night.

Do I go to open the team to look if there is some switch of rearming or reset? Thank you. Luis

Posted: Fri Nov 09, 2007 10:24 am
by andywilks
There is no internal 'reset' switch .
If the blue light does not stay on then the hard drive has become corrupt. The machine has a very limited ability to recover from this corruption. Normally we just have to clone a working 'image' from a good drive to it. you will of course lose all recordings you had. :(

Posted: Fri Nov 09, 2007 12:50 pm
by zoritsu
Hi:

What possibilities do I have of obtaining the image?
It is the same that the HM-HDS1?

Thank you. Luis

Posted: Fri Nov 09, 2007 1:17 pm
by andywilks
The only successful way to do it is a direct clone of the drive. We have tried to rip an image but JVC fill the entire 80Gb with random data that won't compress when trying to put that on a DVDr.

I have UK discs to be able to use, (is yours UK spec?) so I would need you to post the drive here for me to clone for you.